Dydac Controls

• 16 Amps
• 32 Amps

Hot Runner System Specifications:

• Voltage :- 240 volts
• Output Current/ Watts :- 15 amps 3600 watts at 240 1800 at 120
• Input :- Type J thermocouple Grounded or ungrounded
• T/C Break protection :- Inhibits power to heater
• Control Accuracy :- +/-1F or +/- .5C
• Temperature Range :- Ambient to 999F (535C)
• Cycle time :- 0.33 seconds
• Manual control :- Adjustable from 0 to 100%
• Ramp Start :- Duration 5 minutes ( Shortly Introducing )
• Output :- Zero cross triac or Phase Angle Fired triggering
• Compatibility : - Hot runner industrial standard compatible

Additional Information:

• Production Capacity: As per requirement
• Delivery Time: 7-10 days
• Packaging Details: Packed in Corrugated Box

• Gradual phase angle firing soft start
• Power control system
• Built in diagnostics
• Self-regulating power controllers
• Accuracy of /- IOC
• PID accepts J, K Thermocouples
• Phase angle power controllers are used which saves heater life and power, as these are variable automatic power controllers
• Build in soft start in power controllers
• Fast fuses for over current protection
• Power controllers can handle more than 5000 watts in single 2one at 220 Vac.
• Alarm for heater failure
• Alarm for under and over temperature
• In a case of thermocouple failure, one can set percentage of power to the heaters.

• We offer a wide selection of zone capacities to suit almost any control application.
• We provide individual frame sections up to 12 Zones.
• Then up to 48 Zones, these are stacked together.
• These are pre-wired integral units

Hot Runner System Specifications:

• Voltage :- 240 volts
• Output Current/ Watts :- 15 amps 3600 watts at 240 1800 at 120
• Input :- Type J thermocouple Grounded or ungrounded
• T/C Break protection :- Inhibits power to heater
• Control Accuracy :- +/-1F or +/- .5C
• Temperature Range :- Ambient to 999F (535C)
• Cycle time :- 0.33 seconds
• Manual control :- Adjustable from 0 to 100%
• Ramp Start :- Duration 5 minutes ( Shortly Introducing )
• Output :- Zero cross triac or Phase Angle Fired triggering
• Compatibility : - Hot runner industrial standard compatible

Additional Information:

• Production Capacity: As per requirement
• Delivery Time: 7-10 Days
• Packaging Details: Corrugated BOX

• Compatible with industry standards control modules and mainframes
• Accepts Type J thermocouple
• Bumpless auto/manual transfer
• CompuStep® bake out feature prevents moisture at startup
• Built-in loop break for open heater, shorted Triac, reversed or shorted thermocouple
• Preset alarms at 30°F (17°C)
• SafeChange™ “hot swap” feature allows safe removal and replacement of module

Additional Information:

• Production Capacity: As per requirement

• Auto Control Mode: Computer-Calcu Cycle System
• Control Accuracy: -0.1 F (-0.1 c) dependent on the total thermal system
• Temperature Range: 32 to 999F (0 to 537c)
• Temperature Stability: -0.5% of full scale over the ambient range of 32 to 131F (0 to 55c)
• Calibration Accuracy: Better than 0.2% of full scale
• Power Response Time: Better than 0.3 second
• Process Sampling: 100 milliseconds Jumper-selectable
• Adj Comp Step Control Mode: Variable stepping voltage, phase fired
• Adj Comp Step System Duration: Approximately 5 minutes
• Adj Comp Step Output Voltage: Steps approximately from 25v RMS with 240Vac line output phase-fired
• Adj Comp Step Override Temp.: 221F (105c)
• Compensated: Adjustable from 0-100% Maintain output Power to with 1% of setting
• Safe Change Function: Use of the Safe Change feature does not eliminate the need for careful
• installation and removal of the controller.

Input Specifications:

• Thermocouple (T/C) sensor: Type "J" grounded or ungrounded, Type "k" (Jumper-selectable)
• External T/C Resistance: Maximum 100 ohms for rated accuracy isolated from ground and supply voltages
  T/C Isolation: isolated from ground and supply voltages 
• Cold Junction Compensation: Automatic, better than 0.02F/F (0.01c / c) Potentiometric
  Input Protection: Diode clamp, RC
  Input Protection: filter 10 Megohms
• Input Amplifier Stability: Better than 0.05F/F(0.03 c / c)
• Input Dynamic Range: Greater than 999F (0 to 537c)
• Common Mode Rejection Ratio:Greater than 100dB
• Power Supply Rejection Ratio: Greater than 70dB

Output Specifications:

• Voltages: 110 Vac or 240 Vac nominal, single phase
• Power Capability: 15 amperes, 3600 watts 240 Vac
• Overload Protection: 15 amperes, 1800 watts 120 Vac Triac and load use high-speed fuses,
• Power Line Isolation: Both sides are Fused(ABC-15 GBB)Optically and transformer isolation from a line. Isolation voltage is greater than 2500 volts.

Controls and Indicators:

• Set point Control: Two buttons up or down Resolution:1F (1c)
• % Power Control: Two buttons up and down
• Mode Control: Push button switch with LED indicator for manual mode
• Display: TOP: 3-digit filtered LED BOTTOM: 4-digit filtered LED
• Status Indicators: Heater output, Soft-Start, Manual, alarm
• Power On-Off: Rocker Switch

Electrical Power Specifications:

• Input Voltage: 110 ~ 240 Vac,-10%
• Voltage Frequency: 50-60 HZ
• DC Power Supplies: Internally generated, regulated and temperature compensated
• Dimensions: load 2" W * 7" H * 71/2" D(5.08cm * 17.78cm * 19.05cm)

Additional Information:

• Production Capacity: As per requirement
• Delivery Time: 7-10 days
• Packaging Details: Packed in Corrugated box

Additional Information:

• Item Code: HRTC

• 16 Amps
• 32 Amps